How Should I Store My Pool Float?

A lot of pool owners think that they should just toss the old floats and just buy a new one. While it might be tempting to jump into something right away, you should think about how to store your pool float correctly. What follows is a few suggestions for that.

You should have your old float in a bag in a corner of your pool, away from the walls and the pool’s water. Be sure that the bag doesn’t overhang the pool’s edges so that the bag does not tear. In fact, you want to allow enough space between the bag and the edges of the pool so that you can flip the bag around if you need to.

The next thing you should do is cover your old float with some type of material that allows water to get to it but blocks some of the moisture. You can use paper or plastic. You should put the paper or plastic over the top of the old float and then poke holes at intervals in the paper or plastic. For this job, you should use a sharp pair of pliers or a large drill bit.

After that, you should close the hole on the top of the paper or plastic to make it more secure against the edge of the old float. The last thing you want to do is make the float too moist by allowing water to soak into the paper or plastic. You can use a container to keep the water inside, but keep in mind that there is a limit to how much water will be able to go into the container, and your float is probably not that big.

You will find that you have enough room when you first put the old float in the container, but this will cause the liner of the container to be not quite as tight as it could be. So, you should just keep changing the water out of the container.

Be careful when using the container. When you are storing a large number of floats, you might want to try moving the container back and forth. This helps if the container becomes wet, but remember that it is OK if you pour water into the container.

If the container gets full, the way to store the old float properly is to take the container outside to the deck, or it can be tossed into the rain barrel and the container can be left under the rain there. This is a great tip for keeping the float dry if you have a patio, pool table, or other area where the sun gets too hot.

What you should do, however, is to leave the container under the umbrella in the shade, and the only way you should use the umbrella is to let the old float dry under the sun. Otherwise, it will stay a wet mess all summer long. This is just something to consider, but don’t be tempted to use a plastic bucket or bottle to put the float in.

A more recent development is the use of wind-up toys to float the water up onto the float. While this may be a neat idea for kids, it isn’t too practical. If you aren’t too attached to the idea of children floating your float, it can still be good to keep the container inside the pool.

When you are storing your pool floats, you should also consider protecting them from the elements. You can use plastic bags, or even a few layers of plastic sheeting.

A big tip that many people forget to mention is to clean the floats after every use. That means that you should clean the buckets every week or two to keep your float from becoming stained. For this reason, you should use the same containers that you use for your floats.

Storage in that way will also keep your floats dry. In fact, a little bit of dust is a good sign that the float should be stored, because there may be bacteria floating around.

from Product Analyze https://ift.tt/2XzKa4l
via IFTTT

from WordPress https://ift.tt/2Y3clHA

Using A Pool Float As A Life Saving Device

It seems like a simple question but the answer is that you can use your pool float as a life saving device. The first thing to do is to check and make sure that the water around the water fountain is clear. If it is not, add some cleaner into the water and see if the water fountain floats to its normal position.

If the water fountain does not float, try to get in to check on it. If the water fountain floats, the next step is to lower the faucet or pump down by about a foot.

Once the water fountain has been lowered, make sure that it is on the ground. Do not put the pump or faucet back up unless you have access to it. Next, attach a life preserver to the bottom of the fountain. This is a great way to help out someone who may be drowning.

Be sure to go out after you have attached the life preserver. It is very possible that someone could fall into the water fountain if it is not being watched.

After this is done, you will want to go about helping your family members out. If you have someone who is having a hard time breathing, use the pool float as a temporary water balloon.

Next, if you see someone who may be drowning, grab a water balloon and hold it above their head. This will prevent them from being sucked under the water fountain.

The best way to do this is to breathe deeply and when you see someone who would like to breathe, you should give them your water balloon. Be careful that you do not hurt yourself. Once you are sure that this would be safe for them, let them out of the water fountain.

These are just a few ideas that you can use as an example on how to use a pool float as a life saving device. With all the things that are going on in today’s world, this is one thing that we can still have a lot of fun with.

from Product Analyze https://ift.tt/2ByFkvx
via IFTTT

from WordPress https://ift.tt/2Y43GVH

How To Clean My Pool Float With Ease

Pool Floats is a really nifty accessory to have in your pool. They are highly valuable for the reason that they allow you to easily pull out just about any object from your pool and safely and comfortably clean it at the same time. That is if you follow the right steps of course!

In this article, I’m going to share with you exactly how to clean a pool float. It’s not that hard and, in fact, is really quite simple once you know what you’re doing. This technique of cleaning has been around for years and it’s been used by pool owners everywhere for years.

As far as cleaning a pool float goes, the key is to start off with an existing float. So what do I mean by that? Well, if you already have a float on your pool right now then the first thing you need to do is scrape the surface dirt away using a pool cleaner designed for cleaning floats. If you don’t have one of those, don’t worry about it because you can get a decent quality pool cleaner.

Now, let’s move onto the cleaner itself. Next, you need to use a brush to use to completely clean the float as best as possible. In addition to that, you should also use a sponge to clean the area where you will place the float to help keep your float free from dirt and grime.

The next step of cleaning a pool float is to spray the cleaner directly onto the surface you wish to be cleaned. You can either use an airless nozzle or a bottle filled with water.

After that, you should add water to the area where you will place the float. This helps get rid of the water and dirt that are on the outer surface of the float. When you’re done, simply rinse the cleaner off the float and place it back in the pool where you would like it to go.

Now, once you have your pool float rinsed off, you’re all ready to head out and enjoy your float as it was originally intended to be enjoyed. Just remember to always remember to do your research before using anything you use to clean something else for a change.

These are the steps on how to clean my pool float. Take care and stay safe,

from Product Analyze https://ift.tt/2AB7Zzy
via IFTTT

from WordPress https://ift.tt/309keOy